Showing posts with label soldering. Show all posts
Showing posts with label soldering. Show all posts

Saturday, May 2, 2015

Saturday Share - Lessons Learned, or Don't Be Like Me!

Yay, Spring is finally here!  Flowers are blooming, birds are singing, grass is growing, and lots of arts & craft festivals loom in the near future for many of us!  I actually don’t participate in very many, but have one coming up tomorrow, so now is the time for last minute panic and total chaos.

Unfortunately, I have been very distracted this past week...changes in corporate structure and procedures at work, other jewelry deadlines that are looming, bronchitis, and other family/personal events.  So, here is a quick little blog post about what NOT to do!

Last night I decided to work on some pendants for quick necklaces...the main pieces were complete, but I wanted to solder on some little bezel cups and include some tiny cabs for ornamentation.

Rose-cut moonstone, chalcedony and purple chalcedony with sterling bezel cups.
I did the soldering and while I was at my station, worked on a couple of my molten solder pieces that use plumber's solder.  In a hurry, I went up to put my soldered bezel pieces into the pickle and without thinking, tossed all the pieces in, then went about getting dinner ready.

These are what I pulled out..

Copper-plated bezels with sterling ones for comparison.
As you can see, the sterling bezels got copper-plated!  In my rush and distraction, I accidentally tossed the pieces with plumber's solder into the pickle as well which caused the copper to plate to the silver.  While it doesn't look bad, and I could have done it on purpose if I had wanted, I like the look of silver bezels on copper backing.

Unfortunately, the molten solder pieces are a total loss...

Not sure if I can salvage these...the back of the cross was etched as well...I had high hopes for it :(
The pickle is ruined at this point..any silver I put in will get the same copper plating...but, as it turns out, I need to add some more solder to one side of the larger cup, as the last bit didn't flow all the way around.  So the tainted pickle will come in handy to cover the silver solder that I use!

The moral of the story and lesson learned...metalsmithing, torch and chemical use during jewelry making is something that you should save when you aren't tired, sick, or distracted!  Luckily, I didn't have any other type of accident during this session!

Thanks for reading :)


Friday, December 12, 2014

Quick and Easy Grunge Effects...


These are the earrings I made for the last AJE COM challenge and in post for that I mentioned using solder paste to 'grunge  up' the copper washers I was using. Several people has since asked me exactly what I did so I thought I'd share the process here.


Everybody loves a bit of grunge these days it seems and while I was attaching ear wires to the copper washers for these earrings I decided to change the characteristic of the washers very quickly with some solder paste and, if you have some to hand you can do the same. As you probably know solder paste already has flux mixed in with it so it flows very easily. It's not cheap though so you can create interesting effects with just a little touch here and there (I tend to scrape the gungy bits out of the cap for this purpose) although I've used more in these photos just to make it clearer.


So the first step is to place your your clean washer or copper blank on your solder block or charcoal and dot some paste on it...this can be evenly spread or pretty random depending on what effect you're after.  Then you simply heat up the piece with a torch aiming the flame at the metal rather than the paste. The paste will begin to bubble then turn shiny and flow and by moving your torch around you can draw the solder around your blank. Once the solder has melted switch off the torch and quench the piece in cold water.


Of course this process will also work with tiny pallions of traditional strip solder although you will need to use flux with this to get it to flow as with the piece below. I think this method would probably work better by heating the piece from beneath as if sweat soldering but unfortunately I couldn't use this method as one of the legs of my soldering tripod has gone missing and a two legged tripod is about as much use as a chocolate teapot!



Once your pieces are quenched (left hand image below) you can can pickle them to remove the firescale (bottom right image below), tumble, patinate and/or texture them as you wish. Personally I like the effect of the firescale so I tend to remove any that is loose or flaky with a sanding sponge and then texture and polish which can result in some interesting finishes (top right image below). The one thing to remember if you don't tumble is that you have in effect annealed your piece while soldering so it will be soft so work hardening with a leather or nylon mallet is a good idea.


If you give this a go do let us see what you make - you can post pictures on our Facebook page and we'd love to see them.

Lesley

Tuesday, October 21, 2014

Soldering: The Setup


I like to work big - in fact, the bigger the piece, the happier I am. Somewhere along the way, I heard that larger pieces just aren't possible with culinary or butane torches.. but that's all I've ever used, so I just continue to push the envelope.
Clockwise from left: a hollow bead, a Big Ass Ring, and a Big Ass Ring in progress. Each of these is between two and two and a half inches at the largest point.
I have a variety of butane torches that I use for different techniques, and with the exception of pinned stones (which I haven't yet been able accomplish consistently) I haven't encountered anything I wanted to try that they haven't been able to handle. (I wrote about my favorite torches earlier this year.) But my soldering setup is the thing I get the most questions about - and it's really pretty simple.

I start with an oversized floor tile - any ceramic tile from your local home improvement store will do. I add to that a lazy susan base (from the same home improvement store) and a Solderite board. (I get mine from Contenti).


In order to use the setup safely, the Solderite board needs to be secured to the lazy susan base. I use UHU adhesive putty - the stuff you use to keep pictures from going crooked on your walls after you hang them.


It doesn't take much to secure the board to the base - just small pea-sized pieces in all four corners.




Then do the same thing on the bottom corners to secure the base to the tile. This allows the board to be turned while soldering, eliminating the need to move the torch around to heat the entire piece. 




For a lot of folks - especially people new to soldering - the process of keeping an eye on the flame, the solder, the piece and the pick, all while trying to keep the piece heated evenly, is a lot like patting your head and rubbing your stomach while standing on one leg. I first saw the turntable idea in a workshop with Richard Salley and Jessica Jordan, though an annealing pan under the board works in very much the same way. In either case, a turntable of some kind under the board means the torch doesn't need to be moved, which makes it much easier to keep track of where the flame is pointing - a much safer experience for newbies. 

Tim McCreight, in his wonderful book The Complete Metalsmith, suggests using balled up or woven binding wire on top of a soldering board as an alternative to a tripod setup. I prefer a very thin gauge of wire and a moderately dense platform of wire woven around a fairly thick coiled frame - but you should experiment to see what works best for you. The goal is to create air space between the piece and the board, which allows the heat to be amplified and reflected or bounced up to the bottom of the piece.  



The final essential items in my setup are - from left to right - a soldering pick, a pair of diamond tweezers for placing solder pallions, and a pair of long blunt nose tweezers to pick up and move hot items. I have insulated tweezers and a third hand, but I rarely use them. Even for multi-step fabrication projects, this setup is all I need most of the time.

So if you want to work bigger but aren't ready to move to tank-based torches, give this setup and a larger culinary torch a try - you may be surprised by how much you can do!

Until next time -



Tuesday, March 26, 2013

Book Review: Soldering Made Simple

I've been wanting to read this book since it first came out, at least in part because Joe Silvera, its author, is such an engaging, down-to-earth guy. A few years ago, he and his wife Anat moved their studio to Berkeley, California, to focus on opening and running a jewelry school. Since then, Joe has become an extremely popular instructor at Bead and Button, and this book is - I think - a big part of the reason why.


This is a book that is really and truly written for the home jeweler, starting with a thorough discussion of essential tools and equipment. First up is an overview of soldering boards and blocks and even though I have been soldering for several years, I learned a great deal in just those two pages alone.


Each type has a very specific use, and after reading this section I pulled out every board I had and did some sample soldering just to test out the differences. That new knowledge is going to change the boards I use for different soldering jobs going forward.

There is also a very good explanation of the two main types of butane torches and their safe operation. If you've done any reading about soldering, you may have heard the terms "oxidizing", "neutral", and "reducing" in relation to flame types, and if you're like me, you may have assumed that they were only relevant to the big dual-gas studio torches. Well, not only does this book explain them and how they're used, it also provides close-up photos and instructions about how to obtain them with a butane micro torch.


Joe also gives a high-level review of several basic metalsmithing skills, and I would say that if I have one caution to potential readers, it's that the book assumes certain skills in that area which the reader may not actually have. This is a book about soldering, though, so it's hard to nit-pick. Just be aware that in order to be completely successful with some of the projects, you may need to do some additional homework regarding metalsmithing and metal working tools. And the projects are really fun! There's a squashed hollow bead that I'm dying to try and a gorgeous round box clasp that looks deceptively simple. There's even a ring project that includes some really good information on creating bezels from sheet, determining the proper bezel height, and the proper technique for setting a bezel - all a great bonus in a book about soldering.

There are a couple of minor things to quibble over - for example, Joe demonstrates using shears to cut very small, detailed elements out of metal sheet where I would be inclined to use a jeweler's saw. But that is a matter of preference, not technique. And I found myself wondering what the difference was between "light red" and "pink" when evaluating the color of metal as it is heating - some other point of reference might have been helpful for someone like me who cannot always make nuanced color distinctions. Again, though, these are very minor things and don't impact my recommendation of this book in any way.

So if you are new to soldering, this is a terrific choice for your studio library. It is good, basic instruction written in clear, easy-to-understand language and it will help you equip your home studio properly and safely. As a bonus, working through the 12 included projects will not only leave you with a solid grasp of soldering techniques and how and when to use them, it will also give you an introduction to basic metalworking techniques. What's not to love?

Until next time!



Disclaimer: I came this close to attending a one week metal retreat with Joe the year before he moved his studio to Berkeley, California, to open a jewelry school. We exchanged a few e-mails as I tried to make the decision about whether or not to go, and he was as helpful and encouraging as could be. However, Joe and his publisher Kalmbach Books don't know me from Adam. I purchased this book for my own studio and the opinions expressed here are my own, offered without any hope or promise of compensation. Even the links aren't affiliate links.


Thursday, February 21, 2013

Soldering Tips 3 - toggle clasp tutorial



Here it is, the third of my three posts about soldering. Are you ready to put the tips from my first two posts into action? If you haven't read them already I suggest that you read Soldering Tips 1 and Soldering Tips 2 before having a go at this tutorial, but I will take you through everything gently!

This tutorial will show you how to make an unusual toggle clasp - unusual in that the "bar" of the toggle is a daisy with a petal or leaf shaped ring for it to go through, rather than the more usual long bar through a decorated ring or donut of metal. I like my clasps to not look like clasps, as you will probably have noticed if you've visited my Etsy shop!

Anyway, to get started....

You will need:
the basic soldering kit listed in Soldering Tips 1 (although I didn't use third hand tweezers, binding wire or snips, so you can leave those out!)
small blow torch
easy and medium solder paste
chasing hammer
texturing hammer
saw and saw blades
needle file
wire cutters
round nosed pliers mandrel approx 16mm diameter
doming block and wooden punch

You will also need: approx 2cm square piece of 0.8mm sheet metal, 5cm 1.2mm wire and a scrap piece of 0.8mm wire. I have used sterling silver, but as you will see at the end of the tutorial this toggle works wonderfully with copper too.

And here's how to do it!

 

1. Saw a simple daisy shape from 0.8mm (20 gauge) sheet. My daisy has five petals and measures approximately 1.5cm in diameter. File to neaten the edges and hammer the flower to give it a texture.

2.  Dome the daisy gently. I used the largest cup in my doming block and used a wooden punch to help protect the hammered texture.



 3. Melt some scrap into a small ball and, when it has cooled down squeeze a small amount of medium solder paste onto the bottom of the ball - it is on there honest! You wouldn't believe the number of photos I took to try and get a decent view of the solder! If you need a reminder of how to melt scrap into a ball, have a look at my stud earrings tutorial here.

4. Place the ball in the middle of the daisy and solder it in place. Remember that it is the heat of the metal that causes the solder to melt and flow, not the heat of the flame, and the daisy is a much larger piece of metal than the ball is. Heat the petals first, moving the flame in circles around the flower. As the metal takes on a dark reddish tinge (not bright red, that's getting too hot!) move the flame over the centre but keep it moving until the solder melts and flows. Quench, pickle and rinse the flower.


5. Form a small U from 0.8mm wire and place a tiny amount of easy solder onto each tip - again, it is there, honest!

6. Solder the U in place in the middle of the bottom of the daisy as shown, again remembering to heat the flower first as that's the bigger piece of metal. Use insulated reverse-action tweezers to hold the U in place and (this is the bit that takes the most practice) keep the U still while you remove the heat and the solder becomes solid again otherwise it could slip out of place.


7. Cut two 2.5cm lengths of 1.2mm (16 gauge) wire and bend them around a 16mm mandrel - I've used one of my wooden doming punches. You can see that I'm making lots of leaves at once here!

8. Place the pair of bent wires on a soldering brick to form a leaf or petal as shown.

9. Place a generous amount of easy solder paste at each tip. You have to be generous with the solder here as the joins aren't perfect - this is a rare time to ignore the rule that I gave in Soldering Tips 2!


10. Heat the leaf to melt the solder. Keep the flame moving across the middle of the shape and move to each tip in turn as the metal starts to turn red.

11. Use the torch to direct the solder to where you want it to go. Remember that the solder will flow to the hottest part of the metal. In the case of the join I have circled I obviously had the left hotter than the right and so the solder flowed onto that side of the bottom join. I should have compensated by heating up the bottom right more until the solder flowed over there. I added a little more easy solder, heated again and got a good join second time around. Quench, pickle and rinse your work.


12. Hammer the leaf flat and give it a texture if you wish.

13. File the tips round and smooth, and give it a patina if you wish.

And there you have it! I have added a jump ring to both the daisy toggle and the leaf, and (because I can rarely make just one of any new clasp design!) I have made daisies with different textures, from silver and copper, and given some a lovely shine.


I hope that this tutorial, and my previous two posts, have inspired you to give soldering ago or to pick up your blow torch again. But if you are fan of toggle clasps without the time to make your own you can find the daisy toggles I have made here in my Daisychain Extra etsy shop, and some of the other AJE team members have some beautiful toggle clasps in their shops too -


L to R: Floral Toggle by Karen Totten, Flower Burst Toggle by Kristi Bowman, Moss Green Leaf Toggle by Lesley Watt

Jo Tinley
Daisychain Designs

Thursday, February 7, 2013

Soldering Tips 2

This is the second of my series of posts on the wonderful world of soldering. If you missed the first one you can find it here, but before you read any further, a health warning - learning how to solder can lead to creating even more wonderful jewellery and is highly addictive! However, turning on the torch for the first time and then turning it on a piece of silver that you've spent ages preparing can be pretty daunting. Hopefully these tips will help make you feel more confident.

Bangles are one of my favourite pieces of jewellery to make - and my solder joins are hard to find by the time I've finished!

The theory!
When silver is heated to near melting temperature its crystals move apart, opening up microscopic spaces. Soldering uses an alloy that melts before the silver does and then flows into the spaces in the silver, so that the solder actually becomes part of the piece of work. This is why you can file and sand the excess solder from the surface of your work and (hopefully!) leave a piece with an invisible join.

What you need for soldering to work.
First of all, you need a clean piece of work (dirt will stop the solder from flowing) with a good fitting join. If there is more than a very thin hair-line gap between the two pieces of metal then the solder will flow into the two pieces and not hold the join together.

Secondly, you need flux, a chemical that makes the solder flow when it's melted. If you don't add flux to your work then the solder will just ball up rather than flow into the join.

Thirdly, you need the right sized flame. Solder is melted by the heat of the piece of silver, not by the heat of the flame. If you don't use a torch with a big enough flame then the piece of silver won't heat up to the temperature needed, but then again if you use a torch with a flame that is too big on a relatively small piece of silver then you risk melting your work! I've got two hand torches that I use in classes - a small butane torch that I use for small pieces of work, and a larger butane/propane mix torch that I bought in from my local DIY store that I use for larger pieces of work. I've also got a more professional torch that runs on propane gas bottles, but the other two will do for now! You can see the torches in the photos in my first soldering post.

And of course you need some solder! Use just enough to fill the join. It's quicker to cut a new smaller piece of solder than to file off the excess solder afterwards!

When you heat the silver the flux will first of all bubble up - the piece of solder may "jump" off as the flux dries. If it does (and it does it to everyone at some point!) just turn your torch off and move it back again!

The flux has dried and bubbled. The solder is inside the ring and the heat will draw it through the join.
As the silver gets hotter and closer to soldering temperature the flux will start to take on a glassy appearance and the silver will glow a cherry red - if the glow becomes a brighter, orangey red then take the flame away immediately as you are getting too close to melting!

Nearly at soldering temperature - the flux has taken on a glassy appearance
 If your solder doesn't melt and flow then take a deep breath, remember that it happens at times to every silversmith, no matter what their experience, and try again! You will need to quench your work, clean it in safety pickle and apply more solder and flux as needed.

The flame was on the outside of the ring. As the solder flows towards the hottest part it flowed through the join to the front. If I can see a line of solder on the front of the work I know that the join is strong.
Oxidisation forms on sterling silver when you heat it and this needs cleaning off in safety pickle (see the first soldering post) - it will then take on a white-ish appearance.

It is surprising how long you can keep the flame on your silver without getting close to melting it, but the trick is to keep the flame moving and to watch out for the colour changes - as I said, an orangy-red colour shows that you are getting close to melting temperature. I often get my beginners to deliberately melt some scrap silver before they start soldering so that they can see the colour changes that the silver goes through as it gets hotter, and if you do this and want an idea of what to use the melted scrap for, have a look at the earrings tutorial I wrote before Christmas.

A couple of trouble-shooting tips for you:
  • If the solder has jumped to one side of the join rather than through and across the join then you have probably heated up that side more than the other as the solder will flow towards the hottest part of the metal. With more experience you will be able to move the flame to help draw the solder to where you want it to go.
  • If the solder has balled up rather than flowed across the join then you have either directed the flame to much onto the solder itself rather than onto the silver or have not used enough flux.
Probably the most important tip I can give you is to take your time. I find that a lot of beginners I teach think that they have to be very quick with the flame. Afterall, they've just spent ages sawing, filing and sanding, and it's natural to be worried about melting that first piece of work, and to assume that the best way to reduce the chance of melting it is to be as quick as you can. However, if you slow down, keep the flame moving and watch for the colour changes you will actually have far less chance of melting your work and the solder is far more likely to do what you want it to do.

Good luck - and have fun! Soldering opens up a whole new world of jewellery making! My next soldering post in a couple of weeks time will include a tutorial to encourage you to use your soldering skills.

Thursday, January 24, 2013

Soldering Tips 1

I've made jewellery for as long as I can remember, starting, as I'm sure many of us did, with childhood trips to the bead shop to buy beads to string on cord and headpins. For many years wire was my best friend, especially once I learnt how to make my own findings. Then, about 7 years ago, I decided to teach myself how to solder jump rings closed as I was fed up with paying so much for mass produced ones - this was before handcrafted components were easily available on Etsy. I was hooked, and it completely changed my style of jewellery. It has also led me to teaching silversmithing and jewellery design at my local college. Now, one of my favourite possessions is my blowtorch (well, my three blow torches actually), and I find the whole process of watching the solder flow across the join, of using the heat of the flame to draw it to where it needs to be a lovely relaxing way of spending the day!

This post is one of three on soldering giving you some of the hints and tips that I teach my evening class students. This time I'm going to show you the basic tools needed to solder silver and copper, and also talk about the different types of solder available  - and why you can get different types of solder!

This is my soldering area - a little messy, I know, but soldering isn't exactly the cleanest part of making jewellery. You don't actually need a lot of equipment to start soldering. Each tool is quite cheap, although the price can obviously add up, but if you look after the tools well they will last you for years.



Going through the labels we have:
  1. Old slate tiles - left over from a DIY project, these protect the table below from the heat. You can buy soldering sheets that do the same job, but tiles are cheaper!
  2. Soldering block - extra protection from the heat. These also absorb some of the heat from the flame and pass it back into the silver, so if you have several pieces on the block waiting to be soldered (for example if you are soldering lots of links for a chain), they will start to heat up before the flame even touches them. I have a couple of blocks, and if I am soldering a big piece I will prop a couple up behind the block I'm working on to radiate the heat back to the metal.
  3. Charcoal block - used to melt small balls of silver such as in this tutorial
  4. Reverse action tweezers - these take a bit of getting used to as they open when you push the handles, opposite to how most pliers work. This is useful though, as I often use them to hold, for example, an earwire in place on the back of the earring during soldering and I don't have to remember to hold them tightly closed, they do the job for me. They are insulated.
  5. Solder probe - not essential put useful for pushing solder back to where you want it to be if it moves during the process.
  6. Third hand with tweezers - not essential but useful for holding small pieces during soldering.
  7. Torches - I've got two hand torches, and also a propane torch that feeds of a gas bottle under my desk, out of sight. It is the heat of the piece of work that melts the solder, not the heat of the flame, and so if I am soldering a big piece such as a bangle I need to use a bigger torch to heat the silver up enough. The smaller torch is ideal for chains, clasps, earwires etc. The small torch came from Cookson Gold, as did most of my soldering equipment, and the big one is a plumber's torch from a DIY store!
  8. Quench pot - such a sophistcated expensive piece of kit! Never put hot metal in the pickle (more about pickle in a minute - it's not what you put with your cheese sandwich), always quench it to cool it down first. And if you manage to melt the side of it with a hot piece of metal you can always eat some more ice cream to get a new pot.
  9. Goggles - you've only got one pair of eyes!
  10. Binding wire - useful for holding together larger pieces during soldering.
  11. Pennies! - useful for propping up small pieces while you solder them.
  12. Snips/shears - use these to cut solder strips into smaller pieces (pallions) ready to use for soldering.
  A few more bits and pieces for you:

  1. Pickle pot - another expensive piece of equipment! You can buy expensive pickling units, but I use an old slow cooker that cost £2 at a carboot sale. Safety Pickle comes as salts that you mix with water. Always read the safety sheet that comes with it. It is a mild acid solution that cleans off the copper oxides that form on the surface of sterling silver when it is heated. It works quicker if it is warm, but will still work when cold, just a lot more slowly. My pickle sits in a pyrex dish that sits in water inside the cooker. I can't put the pickle straight into the cooker as I haven't got a ceramic insert in mine, it's just steel. If you put steel or iron (eg reverse action tweezers, binding wire) into the pickle, all of the copper the pickle has collected off the silver as it's cleaned the oxidisation off will go back on the silver! Which leads me to....
  2. Brass tweezers - use these to take work out of the pickle instead of steel tweezers. You can also buy plastic tweezers.
This picture shows my soldering materials - flux and solder in various forms.

  1. Borax cone and dish - a cheap and easy to use form of flux. Put a very little amount of water in the bottom of the dish and grind the cone in it to form a milky paste which is then painted onto the silver. Remember solder will only flow, rather than ball up, if flux is present.
  2. Auflux - an artificial form of  flux, again relatively cheap but doesn't last as long as a cone. Again, just paint it on where it is needed.
  3. Solder strips - the traditional form of solder. Cut into smaller pieces (pallions) ready to use for soldering. I have a little pot for each solder - Hard, Medium and Easy - I'll explain those terms in a bit!
  4. Solder paste syringes - a modern form of solder - some people love it, some people hate it saying it's cheating! I say it has got its place and can be useful, but it doesn't replace solder strips. Solder paste is basically ground up solid solder mixed with a flux so that it's ready to use. I only really use it for chain work as I find it more convenient - just work along the row of links waiting to be soldered, squeezing a little bit out at a time! It is much more expensive that solder strips though. Again, I've got Hard, Medium and Easy solder.
So why the different names for solders? Hard, Medium and Easy solders have different melting temperatures - hard has a higher melting temperature than medium (ie. it is harder to melt), medium has a higher melting temperature than easy. You can also sometimes buy extra-easy solder which has an even lower melting temperature, but I find that a bit sluggish to flow and so tend to avoid it. By the way, the different types of solder all form nice strong joins if used properly, the names refer to how hard or easy they are to melt, not how hard or strong the join is.




Why do you need different melting temperatures? Because you often need to solder more than one join on a piece of work, and when you solder the second join, you don't want the first to remelt or it is likely to weakend. Take the Turquoise Shells pendant shown above as an example.The bezel around the cabochon was soldered closed with hard solder, and then after shaping was soldered onto the base plate with medium solder - the temperature needed to melt the medium solder wasn't high enough to remelt and weaken the easy solder. The prongs and the bail were soldered on with easy solder. They were only small pieces to solder on, so as long as I was quick and carefully with what I was doing I could use easy solder on more than one join without affecting the hard or medium solder or the previous easy solder joins. If I only need to solder one join, for example on a bangle, then I just use easy solder as it's easier to melt, but some people prefer to use medium solder as it can be a better colour match to the silver. I use the same techniques to solder copper, and to solder silver and copper together, although I do find that copper needs more flux than silver does.

Do let me know in the comments if you have any questions and please do leave a comment if you have a tip of your own to share!My next post on soldering will be in a fortnight's time so I will do my very best to answer any questions either in the comments below this post or in my next post, which will cover how and why soldering works, how to get it to work (most of the time) and what to do if it goes wrong.

Jo Tinley
Daisychain Designs