Friday, April 15, 2016

Lampwork Buyer Beware

Note: I originally wrote and published this blog post in October 2014. However, I've recently noticed a large quantity of structurally unsound lampwork beads being offered up for sale in Facebook groups, and I just cringe when people buy them. As much as I secretly might want to call out a beadmaker for selling beads whose dots will probably not survive any kind of jostling, I am not the lampwork police. My goal is to educate those who buy lampwork so they know what to look at when considering purchasing a bead.

------------------------------------------------------------

I did something that I am SUPER uncomfortable with, and I'm about to share it with the world....all because I am looking out for those of you who purchase lampwork beads. What is this shameful thing? I made a bad quality lampwork bead. On purpose. Let's start off with a side-by side of the bead with bad technique (left side) next to the "same" bead using good technique I've developed over the last 9 years of lampworking experience. (as an aside, I wasn't going for good design, just an easy to see example)

Sample beads

Why is the bead on the left bad technique? Let me count the ways! I tried to cram as many as possible onto a single bead in the hopes it could be inducted into the Fugly Bead Hall of Shame (I'm pretty sure that's a thing). 

First of all. Raised dots that aren't sufficiently attached to the bead. These WILL break off. In fact, you can see the dot that fell off as I tried to remove the bead from the mandrel. 

Example of horrible quality lampwork bead.

How can you tell if the dots are well anchored to the base bead? The base of the dot that meets the bead, will not have undercuts....meaning, the base will not be narrower than the body of the dot. See the dots in the "good" bead below. They are firmly attached to the bead.


Sample bead

Same with raised stringer designs. If the stringer work has undercuts where the stringer meets the bead, it will break off. See how the stringer below looks like it's just sitting on top of the bead? 


Example of horrible quality bead

The "good" bead below has stringer that is securely attached to the base bead. You can see how it is melted into it rather than still looking fully round in shape. 


Sample bead

I would like to point out that a HUGE no no is when bead makers leave bead release in the bead holes. Properly cleaning the bead release involves diamond drill bits and a tool to use the drill bits. I personally like my battery powered Dremel for that. Not too powerful, but gets the job done. Unfortunately, the battery was dead and the light was fading. So, yeah, my good example still has bead release. However, beads you buy should have the release already cleaned out for you. So check the holes. If it isn't cleaned out, it will flake FOREVER. Fyi: craft store lampwork beads still have the bead release in the holes. 

The next thing you want to avoid when buying lampwork, is bead holes with sharp pointy edges. Let's take a look at the comparison photo again. 

Sample beads

Those sharp pointy bead holes: #1-are not structurally sound. They WILL crumble, chip, and break. #2-will rip beading wire and cord. #3-sharp and dangerous for skin. #4-ugly #5-proof that the lampworker hasn't learned how and/or hasn't taken the time to properly shape the bead. 

The bead holes should be puckered or at the very least, flat. If they are pointy, they should not be offered up for sale. 

Another thing you can see in the photo above, the bead on the left is VERY off center and looks "pregnant." While an off-center bead can be an aesthetic preference, it should be noted when considering your designs and preferences.

The one thing I couldn't reproduce without possibly causing a total explosion, is the crack that results from improper annealing technique. You have the right to ask the lampworker how they anneal their beads. The proper method is annealing each bead as it's made in a digitally controlled kiln. Some will batch anneal, which means to make all the beads, and cool them in a fiber blanket then place all of them in a kiln at once and anneal them. All I have to say is no. This is NOT good annealing technique and has a failure rate high enough that I would never do it. 


The lake house studio is finally set up and functional! #thisartistslife #glassaddictions

As you can see in the photo above, in my lake cottage studio set-up, my kiln is to the left and held (soaked) at 950F during my entire torch session. As soon as I finish a bead, it gets popped into the kiln and held at that 950 degrees until I force it into the cooling (annealing) cycle. This cycle SLOWLY brings down the temperature, allowing all the molecules in the glass to line up properly. A glass bead properly annealed will not shatter, but rather bounce on concrete (it WILL chip though! So don't try it. It IS glass after all). 

Part of the reason I decided to write this post is that I've noticed a huge influx of lampwork being sold that shouldn't be offered up for sale and I prefer people who are spending their hard earned money on lampwork are able to spot quality beads. Because if they buy beads they are ultimately unhappy with, it poisons them against buying lampwork in the future. 

Some of the sellers of these beads are new beadmakers and super excited to be making their own beads. They should be! But selling them is maybe not the best thing. Here are some of my VERY early beads from 2005. Ugly ugly ugly. 


When I started making beads in 2005, my daughter was only 4 years old and loved every bead I made like it was treasure more precious than gemstones and gold. She is now 13 and was cleaning her disaster area (bedroom) a few weeks ago and unearthed this bracelet she made with some of my first beads. Her tastes have changed (thank goodness!) and she gave them back to me. LOL! I am so glad to have these early beads so I can see how far I've come. And I'm so glad no one BOUGHT these beads...



11 comments :

  1. Well said, I totally concur with your post.

    ReplyDelete
  2. Wow I would never know this stuff when buying beads. Thanks so much for the great info!

    ReplyDelete
  3. Thank you so much for this useful information...

    ReplyDelete
  4. Thanks for reposting this reminder. I love lampwork and will be more careful when I purchase.

    ReplyDelete
  5. I wish this could be posted in rules section of every freaking group of "bead makers", on Facebook.

    ReplyDelete
  6. Great comments Jen, and I appreciate the information to share with buyers. It's still a buyer's beware market after all these years!

    ReplyDelete
  7. "Some of the sellers of these (insert handcraft type here) are new makers and super excited to be making their own (insert handcraft item here). They should be! But selling them is maybe not the best thing."

    This advice is not just for new bead makers - it applies to any person who is new to any craft or art.
    So many people believe they can skip the learning phase before they start selling. They don't realize that stuff will follow them around the rest of their lives. The least of the problems it causes is an on-going perception of poor quality, interfering with their ability to price their current work accurately and fairly.
    Great post, Jen.

    ReplyDelete
  8. Everyone starts somewhere. I never really thought about what's a good bead and what's a bad bead. I haven't bought any lampwork yet and so haven't been burned, but now I know what to look for. Thank you for this valuable info!

    ReplyDelete
  9. Thanx for sharing. This is good to know. I just made my first lampworked beads but I would not even consider selling until I have a lot more experience.

    ReplyDelete
  10. This is a great post. I must have read it when you first posted it because I look for those things now when I see lampwork, and I appreciate your sharing these tips!

    ReplyDelete

We would love to hear what you have to say, please leave a comment.